Recent content by MindWalker

I have a faint memory of seeing a blog post or a video mentioning a battery (I remember thinking that I should disassemble the machine to check that, and later thinking that I'd do it once I start looking for the faulty RAM), but I might be wrong. I have seen the machine only ever listed as a...

Here is the DOS 2.11 disk that came with my machine (IMG + flux from Greazeweasel). There are some intresting executables (that do nothing inside emulator and have no /? to explain themselves - I can't remember which of these are just the usual DOS 2 commands) and something to do with the...

I have one of these machines, too. It came with a copy of a boot disc, don't know how much is original but at least it was an Ericsson OEM DOS (old, perhaps 2/3. something?). I'll grab the disc next time I have access to the machine and image it. Last time I booted the machine it complained...

Thanks! This has been perhaps the most demanding build I've done so far... the case needed (and still needs) work, there was a bad SD card, plenty of non-working disk images, a keyboard that prevented me from installing, and quite a bit of learning curve on installing AIX and configuring...

The installation on ZuluSCSI's virtual hard drive did work but as it wasn't quite fast enough, it was a bit sluggish to use. However I was able to use that to mount the old volume group in the bigger of the two original hard disk drive to pull out some files. The printing background was indeed...

I was just able to proceed with the install by trying another keyboard! For some reason the one I was using first worked fine in the System Management Service / boot but stopped working when AIX booted or the installation was started. Now with another PS/2 keyboard I was able to get the...

Ok, I am making some progress here... The machine starting by itself when AC was connected was due to a missing jumper on the remote boot pins on the motherboard, fixed now. I was getting RAM errors but that was because I had it in wrong slots (the manual which covers 140, 150 and 240 models...

Hi. I bought an interesting re-branded IBM 43p; a "CreoScitex Brisque Impose": The bottom sticker says "IBM Italia, Machine Type: 7043-150" so I believe it's simply an OEM thing with custom stickers slapped on to the case. The machine came without a PSU or RAM, but since a helpful member...

I bought one from Wildfire (thanks again - the computer works now!) so this thread can be closed/archived.

I can't be sure, but I have a ATEN CS-104 Master View which looks identical (apart from case color and front panel graphic). The Aten's manual says the RJ11 is for connecting an external foot switch and shows the pinout: https://www.manualslib.com/manual/10804/Aten-Cs-104.html?page=10#manual

I believe I have the very same motherboard. This is the closest-looking model that I've found: https://stason.org/TULARC/pc/motherboards/A/ACER-INC-486-KMX-AL25-33SX.html I was just recently using the motherboard to test something and I couldn't find my placeholder-battery-solution that I used...

Thanks! That cordless phone of yours looks great, @Torch. The leather looks stunnigly good for the age. Are those even leds or just small bulbs? I haven't been able to figure out much more, but I've keep working on getting a known-good test setup first with newer modems and my VoIP box (still...

Perhaps all three won't have the same damages and perhaps you can get at least one good out of them :) (If you end up with an extra CRT with life left on it, I might be interested ;) ) Can you post an image of the 3210 control panel? Sounds like a neat project if you could hook it up to a Pi...

That looks rough, good luck (y) The vent holes on the rear are somewhat recessed so perhaps the insides are not as bad as the exterior. I have a working unit (although with a very worn CRT), haven't been able to find a schematic or a service manual. I've added a list of electrolytics into the...

Hello all. I bought this gem for 8 EUR. About the only thing that comes up on google is the auction where I bough this. It's missing the buttons on the front, also there was no power supply but the PCB text says 20V (AC) and using a US Robotics 20vAC PSU (from a much later modem) does work...