• Please review our updated Terms and Rules here

Search results

  1. A

    Midwest Floppy disk controller board for Xerox 820-II

    Well, I didn't get that far since the high voltage wasn't working I just put it away until I figure out what to do next. I'll try the HOT as a longshot but if that doesn't work I'll just ditch the CRT. Troubleshooting the mainboard should be okay since it's all discrete logic and I even have...
  2. A

    Midwest Floppy disk controller board for Xerox 820-II

    Did some further work on the machine. The power supply had some cracking Rifa line filters so I replaced those. Nice steady output on all the rails. The CRT filament glows but there is no high voltage. The flyback transformer was hanging off the board. It looks like one of the two mounting...
  3. A

    Looking for a replica of the original CP/M 2.2 8 inch disk

    By the way, the original CP/M was FM disks and used the worst-case data pattern of hex E5 for the blank sector data, and thusly the "erased" directory entry value. Later when machines started using double density, CP/M still had to use E5 even though it was no longer the worst case data...
  4. A

    cdos, Cromix and ram

    Actually I think that board is the only static RAM board I've seen that will work (it is new to me). It fully implements the bank assignment for all eight positions including the ability to always map the high bank for all boards in the system when bit 7 is selected.
  5. A

    cdos, Cromix and ram

    Are you certain 64KZ are not supported by Z80 Cromix? Mine seem to work fine. Back in the day my 11.27 system ran on a set of CCS 2066 boards. I have only ever owned one 64KZ-II which was that awful early revision B board that got bounced around between several people and the seller last...
  6. A

    cdos, Cromix and ram

    For Z80 Cromix (versions up to 11.27) you need a Z80 CPU, a 16FDC with modifications to support the Shugart drives, and a minimum of two 64KZ RAM cards. A TUART would be needed to support additional concurrent user logins as well as the required additional RAM banks. There are no static RAM...
  7. A

    Qume Terminal membrane keyboard repair

    If you find the 8048 is bad, we can work out a mutually beneficial arrangement. Lend me the keyboard for a couple of weeks. I will program a replacement 8748, run some scans of the communication between it and the terminal, then return it to you with a new controller installed. I originally...
  8. A

    Looking for FDC timing chip or substitute for TRS-80 model 4 Gate Array

    I understand the service manual gives some data on the various custom logic parts, perhaps enough to reproduce it. Have you checked there?
  9. A

    Qume Terminal membrane keyboard repair

    That was my fallback plan if unable to find a sample to examine. The main controller code is 8KB of 6800 so also manageable if all else fails. It's supposed to be a bidirectional one-wire protocol so it might be necessary to see both sides. Maybe not. I'll be poking through that. Thanks for...
  10. A

    Qume Terminal membrane keyboard repair

    I just received a QVT-102 from the Pacific NW via eBay. No keyboard. I'd like to reverse engineer the interface so we can build an adapter to us a PS/2 or USB keyboard. But neither of the Qume manuals for this terminal document the protocol. If anyone would be willing to lend me their...
  11. A

    Power supply information for Xerox 820?

    It's surprising how little documentation still exists for a system that was so popular in the day. I think when people moved on to the PeeCee world they binned much of it. Thankfully enough still exists to keep going. I have an 820-II for which I'm going to recreate the floppy disk controller...
  12. A

    TRS-80 PT-210 Data Terminal - keyboard repair, ROM dump, RS-232 board reproduction ... ROM hacking?

    Nice work, fellas! I suspect it was a marketing requirement to make it upper case only. Very likely they didn't want to hurt the sales of some other product(s) in the catalog. Possibly printers.
  13. A

    TRS-80 PT-210 Data Terminal - keyboard repair, ROM dump, RS-232 board reproduction ... ROM hacking?

    Wow, that's great progress! I have no doubt that adding the character bitmaps to the table along with the minor code changes to eliminate the translation to upper case will produce the desired results. This will be one of those milestone moments in retrocomputing history where something...
  14. A

    TRS-80 PT-210 Data Terminal - keyboard repair, ROM dump, RS-232 board reproduction ... ROM hacking?

    Being experienced in MCS-48 for many years, I had some plans to look into disassembling the ROM to see if lower case can be implemented. Technically there should be no problem but who knows how gnarly the code is. But I have a long backlog of things to work on so it will take me a long while...
  15. A

    The curse of fake parts out of China.

    Testing is key. Too many things in the retro community have to be sourced from places where you can't count on the authenticity of the product. BTW, thanks for all the awesome designs you've shared over the years. I purchased one of your ETA-3400 boards a while back and look forward to...
  16. A

    Need help with TRS-80 PT-210 Data Terminal

    Ok, it took longer than I anticipated to circle back around to testing this. A number of things demanded attention and then the arctic blast. But after reviewing the schematic diagram to understand the cabling I successfully hooked it up to a desktop computer. The two switches must be set...
  17. A

    Need help with TRS-80 PT-210 Data Terminal

    It fits well and I only detect a fraction of a mm bend in the pins, which might not even be the result of misalignment. I will have some time tonight to try out communications. I think it would engage more robustly if the pins were a couple of mm longer, past the edge of the board.
  18. A

    Need help with TRS-80 PT-210 Data Terminal

    @Tarkie101 Looking closely at your photo, it looks like you have the board inserted upside down. The header is 36mm from one side, and 38mm from the other. If you turn it around and insert it, the connector footprint and the machine socket should line up better.
  19. A

    CDOS and TU-ART serial board drivers

    Do you have access to a TL-866 family device programmer? You can pull each of the socketed 74 series logic parts from the PRI and test them.
  20. A

    CDOS and TU-ART serial board drivers

    Do you have the earlier PRI (about half the board area populated and no priority pins) or the later one (most of board covered with parts and has the priority chain connector)?
Back
Top