Search results

Ok, that was easy... Do not attempt to build this software on anything older than "current" Linux, I have tried on a debian 11 and it just compiled without issues. Make sure to install all pre-requisite packages mentioned on this document...

Hi all, sorry to revive this old thread, but: did anyone find a way to actually build the fluxengine host tools on any linux distribution? Getting the current source tree from github then following the build instructions (they just seem to suggest it should build with a "make") throws errors...

Hi all, I was trying to impose some order to the spare IC mess. I've found 4 AM27S35DC proms, date codes from 8322 to 8331. Marked as: LM8409 198F3 LM8412 193F3 LM8412 199F3 LM8413 195E3 LM8413 195F3 (this one seems marked twice) I can't recall where they come from. I've dumped them all and they...

Hi all, simple question (I think): what other FDC controller is compatible with the MB8866 at software level? I'm not interested in pinout compatibility, just having something that doesn't need any software change. I guess the FD1791 is, as that seems hinted on the Fujitsu datasheet. Anything...

Hi all, I've recently got a large-ish set of various ROMs and I'm checking and sorting them all. I've found a few 82S115 PROMs that have a Tektronix part number on them: 160-0028-00 (8080 EMU PROM) 160-0027-00 (8080 EMU PROM) 160-0029-00 160-0025-00 It seems they belong to the 8001/8002A...

This is my Apple ][ (europlus), though the board revision I have is older than yours. This is cranking up the monitor brightness. I think I can barely guess some vertical bars in the picture, but in real life they're not visible. It might be a known artifact of the Apple ][ that I'm not aware...

Hi all, as part of an arcade PCB repair (vintage cpu board, so kind on topic!), I need a new MB7052 256x4 TTL PROM. I can't program TTL proms with my current programmers (and I've been trying to find a suitable old Data I/O for years in EU, with no luck). I'm looking for someone that can program...

Hi all, I've just completed and tested my replacement for the 16K Language Card: https://www.youtube.com/watch?v=1KPIAoO1dTU Now, what is the next most useful expansion card for a ][+ machine (actually an europlus)? I'm considering to make a PAL card, a Z80 card, an 80 column (MC6845 based)...

Hi all, I have two 80 col/64k cards for the Apple IIe (and no IIe in sight in any near future). One card is original Apple, the other one is an italian clone (Asem). I'd swap one of them with a disk ][ interface card if anyone happens to have a surplus one. Due to shipping costs, this...

Hi all, as some of you might know, I am good enough at repairing vintage computer things (mostly CBM, but not only). I've made a few videos of my repairs. One of my viewers, living in Australia, asked me if I could repair his 1571 disk drive. Now, I'm sure I could, but shipping costs from and to...

Hi all, I'm not exactly an Apple expert, but I surely have a long enough record of repairs (starting in the middle 1980s). Now, the Apple //e wikipedia page: https://en.wikipedia.org/wiki/Apple_IIe currently states: "The IIe also switched to using newer single-voltage 4164 DRAM chips instead...

Hi all, I've got this old Sunshine IC tester, I believe it was used in a IIe, now long gone. Does anyone have any information about it? A copy of its software would be very welcome of course. Thanks in advance! Frank

Hi all, sorry for the stupid question but I haven't seen many of these in my life (yet). Can an apple ][ europlus (rev.7 motherboard) start normally with no keyboard attached? I mean with the flat cable's dip connector removed from the motherboard. I ask because the keyboard is composed of two...

Hi all, I've just received a 2001N (32k, Basic4) PCB to repair. The owner said it was working for few seconds, then the cursor disappeared and after that, it just displayed the usual garbage screen. Within the first inspection I've found a 4116 chip split in half. This board has all ceramic...

Hi All, I'm in a apple II repair month :) I have this Astec AA11040C supply that had the usual smoked rifa X2 capacitor. Other than that, it's outputting about 5.5V on the +5V line and 13V on the +12V line. However, with a 7 ohm load on +5V, the rail goes to 5.0V. I'll check the ESR of all...

Why following the correct checklist is always good: https://www.youtube.com/watch?v=pZhkVyW394Y

Hi all, I've got a nice Apple II europlus to repair. Unfortunately, it has no cards. I have in my spare box a few RAM, 80 cols, super serial cards and a few more, but no floppy disk drive cards (though I have a spare disk drive). Is there any project to make a compatible card or I better roll...

Hi all, I'm going to get my first arcade PCB to repair (I got one from ebay, just to have fun). It's a Galaga clone, pre-jamma of course. I don't know yet how close to the original schematic this clone is. However, what would be the right place to ask for informations about these kind of...

Hi all, I'm in search of an affordable Apple II clone. I'm not interested in the Apple logo, so I'm just looking for something cheap and even not working, as I believe I can fix it anyway. I've seen a few clones on ebay, the ones really looking as the original II or IIe, in other words, the ones...